From 95af192c99459c56bb30763afd93582a524efc3a Mon Sep 17 00:00:00 2001
From: Marti Bolivar <mbolivar@leaflabs.com>
Date: Mon, 25 Apr 2011 21:23:00 -0400
Subject: Better debug port support.

- gpio.h: afio_mapr_swj_config() renamed afio_cfg_debug_ports()

- [new] wirish_debug.h: disableDebugPorts(), enableDebugPorts()

- Maple, Maple Native, and Maple RET6 PIN_MAPs are now larger by 5,
  have mappings for the extra JTAG/SW pins.

  Documentation was updated appropriately.
---
 examples/test-session.cpp | 79 +++++++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 76 insertions(+), 3 deletions(-)

(limited to 'examples')

diff --git a/examples/test-session.cpp b/examples/test-session.cpp
index d97d0ca..1d9daf0 100644
--- a/examples/test-session.cpp
+++ b/examples/test-session.cpp
@@ -27,8 +27,10 @@ void cmd_serial1_echo(void);
 void cmd_gpio_monitoring(void);
 void cmd_sequential_adc_reads(void);
 void cmd_gpio_qa(void);
-void cmd_sequential_gpio_writes(void);
+void cmd_sequential_gpio_toggling(void);
 void cmd_gpio_toggling(void);
+void cmd_sequential_debug_gpio_toggling(void);
+void cmd_debug_gpio_toggling(void);
 void cmd_but_test(void);
 void cmd_sequential_pwm_test(void);
 void cmd_servo_sweep(void);
@@ -148,13 +150,21 @@ void loop () {
             break;
 
         case 'g':
-            cmd_sequential_gpio_writes();
+            cmd_sequential_gpio_toggling();
             break;
 
         case 'G':
             cmd_gpio_toggling();
             break;
 
+        case 'j':
+            cmd_sequential_debug_gpio_toggling();
+            break;
+
+        case 'J':
+            cmd_debug_gpio_toggling();
+            break;
+
         case 'B':
             cmd_but_test();
             break;
@@ -266,6 +276,8 @@ void cmd_print_help(void) {
     SerialUSB.println("\tU: dump data as fast as possible on USB");
     SerialUSB.println("\tg: toggle GPIOs sequentially");
     SerialUSB.println("\tG: toggle GPIOs at the same time");
+    SerialUSB.println("\tj: toggle debug port GPIOs sequentially");
+    SerialUSB.println("\tJ: toggle debug port GPIOs simultaneously");
     SerialUSB.println("\tB: test the built-in button");
     SerialUSB.println("\tf: toggle pin 4 as fast as possible in bursts");
     SerialUSB.println("\tr: monitor and print GPIO status changes");
@@ -534,7 +546,7 @@ void cmd_gpio_qa(void) {
     }
 }
 
-void cmd_sequential_gpio_writes(void) {
+void cmd_sequential_gpio_toggling(void) {
     SerialUSB.println("Sequentially toggling all unused pins. "
                       "Press any key for next pin, ESC to stop.");
 
@@ -582,6 +594,67 @@ void cmd_gpio_toggling(void) {
     }
 }
 
+uint8 debugGPIOPins[] = {BOARD_JTMS_SWDIO_PIN,
+                         BOARD_JTCK_SWCLK_PIN,
+                         BOARD_JTDI_PIN,
+                         BOARD_JTDO_PIN,
+                         BOARD_NJTRST_PIN};
+
+#define N_DEBUG_PINS 5
+
+void cmd_sequential_debug_gpio_toggling(void) {
+    SerialUSB.println("Toggling all debug (JTAG/SWD) pins sequentially. "
+                      "This will permanently disable debug port "
+                      "functionality.");
+    disableDebugPorts();
+
+    for (int i = 0; i < N_DEBUG_PINS; i++) {
+        pinMode(debugGPIOPins[i], OUTPUT);
+    }
+
+    for (int i = 0; i < N_DEBUG_PINS; i++) {
+        int pin = debugGPIOPins[i];
+        SerialUSB.print("Toggling pin ");
+        SerialUSB.print(pin, DEC);
+        SerialUSB.println("...");
+
+        pinMode(pin, OUTPUT);
+        do {
+            togglePin(pin);
+        } while (!SerialUSB.available());
+
+        digitalWrite(pin, LOW);
+        if (SerialUSB.read() == ESC)
+            break;
+    }
+
+    for (int i = 0; i < N_DEBUG_PINS; i++) {
+        digitalWrite(debugGPIOPins[i], 0);
+    }
+}
+
+void cmd_debug_gpio_toggling(void) {
+    SerialUSB.println("Toggling debug GPIO simultaneously. "
+                      "This will permanently disable JTAG and Serial Wire "
+                      "debug port functionality. "
+                      "Press any key to stop.");
+    disableDebugPorts();
+
+    for (uint32 i = 0; i < N_DEBUG_PINS; i++) {
+        pinMode(debugGPIOPins[i], OUTPUT);
+    }
+
+    while (!SerialUSB.available()) {
+        for (uint32 i = 0; i < N_DEBUG_PINS; i++) {
+            togglePin(debugGPIOPins[i]);
+        }
+    }
+
+    for (uint32 i = 0; i < N_DEBUG_PINS; i++) {
+        digitalWrite(debugGPIOPins[i], LOW);
+    }
+}
+
 void cmd_but_test(void) {
     SerialUSB.println("Press the button to test.  Press any key to stop.");
     pinMode(BOARD_BUTTON_PIN, INPUT);
-- 
cgit v1.2.3