1 files changed, 81 insertions, 0 deletions
diff --git a/package/udev/S10udev b/package/udev/S10udev
new file mode 100755
index 000000000..220fbcef6
--- /dev/null
+++ b/package/udev/S10udev
@@ -0,0 +1,81 @@
+#!/bin/sh
+#
+# udev	This is a minimal non-LSB version of a UDEV startup script.  It
+#	was derived by stripping down the udev-058 LSB version for use
+#	with buildroot on embedded hardware using Linux 2.6.12+ kernels.
+#
+#	You may need to customize this for your system's resource limits
+#	(including startup time!) and administration.  For example, if
+#	your early userspace has a custom initramfs or initrd you might
+#	need /dev much earlier; or without hotpluggable busses (like USB,
+#	PCMCIA, MMC/SD, and so on) your /dev might be static after boot.
+#
+#	This script assumes your system boots right into the eventual root
+#	filesystem, and that init runs this udev script before any programs
+#	needing more device nodes than the bare-bones set -- /dev/console,
+#	/dev/zero, /dev/null -- that's needed to boot and run this script.
+#
+
+# old kernels don't use udev
+case $(uname -r) in
+    2.6*|2.7*)	;;
+    *)		exit 0;;
+esac
+
+# Check for missing binaries
+UDEV_BIN=/sbin/udevd
+test -x $UDEV_BIN || exit 5
+UDEVSTART_BIN=/sbin/udevstart
+test -x $UDEVSTART_BIN || exit 5
+
+# Check for config file and read it
+UDEV_CONFIG=/etc/udev/udev.conf
+test -r $UDEV_CONFIG || exit 6
+. $UDEV_CONFIG
+
+# Directory where sysfs is mounted
+SYSFS_DIR=/sys
+
+case "$1" in
+    start)
+        # mount sysfs if it's not yet mounted
+        if [ ! -d $SYSFS_DIR ]; then
+	    echo "${0}: SYSFS_DIR \"$SYSFS_DIR\" not found"
+	    exit 1
+        fi
+        grep -q "^sysfs $SYSFS_DIR" /proc/mounts ||
+	mount -t sysfs /sys /sys ||
+	exit 1
+
+        # mount $udev_root as ramfs if it's not yet mounted
+        # we know 2.6 kernels always support ramfs
+        if [ ! -d $udev_root ]; then
+	    echo "${0}: udev_root \"$udev_root\" not found"
+	    exit 1
+        fi
+        grep -q "^udev $udev_root" /proc/mounts ||
+	mount -t ramfs udev $udev_root ||
+	exit 1
+
+        mkdir $udev_root/pts $udev_root/shm
+
+        # populate /dev (normally)
+        echo -n "Populating $udev_root using udev: "
+        echo -e '\000\000\000\000' > /proc/sys/kernel/hotplug
+        $UDEV_BIN -d || (echo "FAIL" && exit 1)
+	$UDEVSTART_BIN || (echo "FAIL" && exit 1)
+        echo "done"
+        ;;
+    stop)
+        # Stop execution of events
+        udevcontrol stop_exec_queue
+        killall udevd
+        ;;
+    *)
+        echo "Usage: $0 {start|stop}"
+        exit 1
+        ;;
+esac
+
+
+exit 0